"Thank you for the time you took helping me determine the best way for me to EZ Slide my boat trailer's four bunks and guides, and for helping me figure out how to equip my friend's boat trailer as well. I wish more businesses were so helpful."
- Frank B.
Home > Anchor Pullers >
Anchor Ring Stainless Anchor Retriever by Ironwood Pacific
Anchor Ring Anchor Retrieval
Anchor Ring anchor retrieval is designed for offshore applications where longer lengths of anchor chain are common. Our Anchor Ring has been specifically engineered to offer exceptional performance and value to boaters. Once you have used our Anchor Ring anchor retrieval, you will never want to go back to hauling your anchor by hand again.
Key Features of Anchor Ring Anchor Retrieval
- Can lift up to 80 lb anchor systems, depending on the capacity of the buoy
- Stainless steel ring and shackle
- Designed for anchor lines rigged with more than 15 feet of chain
- Easy to use - just slip over your anchor line when ready to raise anchor
- Can be used with any size buoy
- Available in 2 models
- Anchor Ring Standard is contructed from 1/4" stainless steel
- Anchor Ring Heavy-duty is constructed from 5/16" stainless steel
- Lifetime warranty
- Made in the USA
Anchor Ring Buoy Options
| Standard Buoy|| 11.5"|| 30 lbs.|| Red, Yellow|
| Large Buoy|| 15.5"|| 60 lbs.|| Red, Yellow|
| Jumbo Buoy|| 18.5"|| 80 lbs.|| Red, Yellow|
How does Anchor Ring anchor retrieval work?
| 1. Slip the Anchor Ring over the anchor line. Attach the shackle- buoy assembly. Be sure to snap the shackle through both eyes of the ring. Toss the buoy into the water allowing the ring to slide down the line.
|| 2. Motor your boat at a 30 degree angle off of your anchor point, taking care to keep the anchor line clear of the prop. Proceed slowly (roughly 5 knots) until the anchor is released from the bottom. Then increase speed slightly.
|| 3. The anchor line will slide through the ring as the buoy floats on the surface. Once the anchor has reached the surface, shift into neutral and pull in the slack anchor line and anchor. The anchor chain will counterbalance the anchor and hold the anchor at the surface.
Watch anchor retrieval in action
Anchor Ring Anchor Retrieval System Resources
Watch the AnchorLift anchor puller in action
How To Inflate a Polyform Buoy by Ironwood Pacific Outdoors - SavvyBoater.com Videos
Today, we are going to show you how to properly inflate a Polyform buoy.
First, use a flathead screwdriver to unscrew the cap from the air valve.
You may use either an air compressor or a Polyform Hand Pump to inflate the buoy.
If using an air compressor, set the compressor to 30 psi or less, place the compressor nozzle over the valve airway of the buoy, and inflate up to a maximum of 2 psi.
No special attachment or tip is needed.
When using the hand pump, simply insert the nozzle into the air valve and pump until full.
The valve flap may not fully open when using a Polyform Hand Pump; therefore, you may need to insert a blunt object--such as a small screwdriver or awl--prior to inflation.
After inflation, you should be able to make a quarter-inch indentations with your fingers.
However, the buoy should still be fairly firm.
Then, use your screwdriver to tighten the cap back into the valve.
How To Clean a Polyform Inflatable Buoy - SavvyBoater.com Videos
Clean Polyform fenders look good, and they help keep your boat clean.
The simplest way to clean a Polyform fender is to try using soap and water.
After the fender is dry, a common protectant, suitable for vinyl or plastic, provides a nice finish.
Properly inflated and cared for, Polyform fenders will provide years of excellent service.
How to Inflate a Polyform Fender with a Compressor - SavvyBoater.com Videos
When you a purchase a Polyform fender, chances are they're going to come in a box like this.
When you open that box, what you're going to have...is something that looks like this, which is the fender.
Now, it's not inflated.
How in the world am I going to inflate this?
When customers receive our fenders, normally the screw is halfway in.
The screw has to be taken out, and it can be done either with a quarter or a screw driver.
Put the screw driver into the screw, turn it counter-clockwise, and take it out.
Most customers like to use an air nozzle to fill their product.
When inflating the product, make sure that your air compressor is at 30 pounds of pressure or less.
Stick the rubber nozzle into the product.
How do we know how much air to put in this?
All of our products should have 2 pounds of air pressure.
Fill the product until you can push in a quarter of an inch on the side.
Well once the product is inflated to two pounds of pressure, we need to put the valve screw back into the product.
Make sure that we only go down to the face of the valve and no further in.
You will feel resistance. Once you feel that resistance, stop.
This is ready to go.
All I need is a piece of line, which we call a fender rope, and this is ready to go on a boat.
How to Inflate a Polyform Fender with a Hand Pump - SavvyBoater.com Videos
Using a Polyform Hand Pump to inflate a Polyform fender is very simple.
First, using the proper-sized screw driver, remove the plug.
Next, insert the pump nozzle and inflate.
Do not over-inflate.
The wall of the fender should be flexible.
Finally, re-insert the plug.
When the plug is flush with the surface, tighten until snug.
The fender is now ready for use.
|Ironwood Pacific Shipping Rates |
Lower 48 US states
Call for Quote
At Ironwood Pacific Outdoors we strive to expedite all orders. Your order will typically be processed and ready for shipment within 1 to 2 business days.
Orders are typically shipped via FedEx Ground. Although occasionally, depending upon destination and weight, we may ship items via other means including US Mail. If you order multiple items, the contents of your order may ship in more than one box.
Our shipping rates to domestic customers in the continental United States (excludes Alaska and Hawaii) are based on the value of the order. The following table outlines our standard shipping rates.
For shipments to destinations outside the continental United States, we will be happy to provide you with a quote. Please complete our Shipping Quote Request form.
Typical FedEx Ground Transit Time for Products in Business Days
Exactly what I wanted. I first saw them in Alaska and knew it was what I need to pull the anchor on the Columbia River in Oregon.
Based on research this product appeared to have highest quality; validated when I received.
Shipping was quick.
I am very satisfied with the purchase.
Anchor Ring Stainless Anchor Retriever by Ironwood Pacific (0002)
i haven't used it yet but not exactly prudent of Ironwood to not send instructions on how to inflate the ball. I unscrewed the screw went to attach my bicycle pump to discover the normal valve doesn't fit. I took it to the west Marine store and they didn't have a valve nor did they know how to fill it. I finally called your customer service and got instructions to watch a video and how to use a compressor air pump, etc. etc. JUST ADD THE INSTRUCTIONS.
Great product but 80lbs or 60lb lift?
This is was an awesome purchase!
Was a little skeptical about what the lifting power was on this ball.
The description says "pulls up to 80pounds"
When I received it the product says it pulls up to 60pounds!
I run a 25 foot chain (31 pounds) coupled with a 28 pound anchor.
Only way to try it out was to put it through its paces. Note: I have purchased severs balls in the 14 inch and 18inch size range and only this one has been able to pull my chain and anchor with easy!